The transmission in my 2015 Silverado failed this past Tuesday. I noticed some random RPM changes without explanation which made me suspect something wasn't right. That escalated quickly to 500 RPM swings and it suddenly seemed to be in neutral. I was coasting to a stop light where I needed to turn so I stopped on the shoulder. When I tried to take off, it would not shift from first gear. I had it towed to a local transmission shop and have been daily driving the Mustang since. As of today (Saturday - 11/14), the Mustang has 82,504 miles so almost 1,000 since purchase.
I decided after working on the intake that I was not going to start any type of major project until about December. The goal was to be able to enjoy driving the Mustang when the weather is the best here. That was a great decision as it allows me to drive the Mustang while the truck will be stuck at the transmission shop for at least another week. While enjoying the car, driving it this much helps me to test it out, grow more confident, and fine tune the various small things you don't always think to do with the larger projects heavy on your mind (make it faster!).
One small item that is annoying is that the key seems to catch in the ignition cylinder randomly. It almost seems as if the inside of the cylinder is still twisted slightly but the main bezel part is not. I decided a while back to purchase and install a black single key conversion kit from LMR (LRS-21984-SK). It would fix the ignition weirdness, switch to a single key, and give me black locks instead of the current stainless appearance on the exterior doors and hatch. I decided today would be a good day to start that project.
I started with the ignition and the glove box. It took a few minutes to figure out how to remove each of them but was generally a fairly easy job. I had to remove the plastic panel under the steering column to access a plug that connects to the ignition cylinder. While that panel was off and the glove box was disassembled, I put some of the SoundSkin foam anti-rattle strip material on the surfaces that touched to eliminate the potential for rattles.
I moved on to the hatchback lock which is where I hit a few challenges. It was at this point, I noticed the black finish was coming off the edges of the new lock. You can't tell when installed but doesn't bode well for the longevity of this part. I might end up contacting LMR but to swap it, I need to remove the ignition and glove box switch I just installed. With that in mind, I went ahead and installed the lock.
I worked on the hatchback before and the strike bar was very worn. I purchased a new on recently from LMR (#LRS-40442C) and installed it today. Since I was working on the hatchback area, I also pulled out the Fairchild hatch seal (#KF3007) that I purchased from Rock Auto last month. The seal looks almost exactly like the original but is thicker and should seal much better. I've very pleased with the Fairchild seals I've purchased to this point. The hatch seals so much better now. I have window channel, door, and sunroof seals that I can install. I believe the sunroof seals have been replaced before but I'm going to change them out anyway when I replace the headliner.
An additional change I had planned was to swap out the front and back Ford oval emblems with some that are black and chrome rather than blue and chrome. Since I was working on the hatch area, I decided I'd start with that one made by Daniel Carpenter (#LRS-614258BK). I pulled the original one off and found there was a small rust spot under it to treat. I was able to address that with Eastwood's Rust Encapsulator and then put the new emblem in place.
I decided to do a little work on the driver side door. I replaced that lock cylinder which was fairly smooth except installing the old lock rod. I then touched up the paint on the speaker panel as it had a strange off color spot. I installed the new Fairchild window channel stripping which was better than the Daniel Carpenter which was installed (better flocking and consistent exterior appearance to the rubber). The last step was to evaluate a little dent I found in the door after all the speaker work to consider if I think it can be reasonably accessed for paintless dent repair. It seems it can but as luck would have it, I covered the back side of it with sound deadening.
I also removed a spacer that I had in place on the throttle cable. It was used with the original throttle body to get it to fully open. However, I now believe it is causing the AccuFab throttle body to stay open a bit to much. It doesn't happen at start up but just returning to idle.



